Toshiba aircon 19 error code & blinking light
Use this Toshiba 19 guide to decide when to stop resetting, what to capture, and what to check before parts are quoted. Match the model first; same-looking signals can point to different rows.
What does Toshiba 19 mean?
Toshiba 19 is listed as tD discharge-pipe temperature sensor disconnected or shorted and tD discharge-pipe temperature sensor error in Multi-Split, Wall-Mounted Split, Single-Split rows such as YouMe 2.0 System 5 - RAS-5M51U2ACVG-SG, RAC TU2C-LINK Interface - Residential AC type. The loaded row is source-backed by official diagnostic material. Do not collapse this code across model families; use the model, series, or system type to choose the right row. Confirm the exact model, series, or signal row before accepting a parts quote.
Open, shorted, displaced, or out-of-range thermistor or pressure-sensor reading.
Loose sensor connector, damaged sensor harness, or water-affected wiring.
PCB input fault after the sensor and wiring readings are confirmed.
What to do now
Use these steps before another reset, sensor check, or PCB quote.
Treat it as a fault signal
If 19 returns or cooling is still abnormal, stop treating it as a simple reset issue.
Reset 19 once
Capture the 19 pattern first, then power-cycle once only and note whether the same fault returns.
Send these to us
19 error code and blinking light, a clear display photo and blinking-light video if the unit shows one, Toshiba model stickers, affected rooms, reset result, and when the fault appears
Source-specific guidance
These diagnostic-reference notes help match the code to the exact model. Electrical, refrigerant, wiring, resistance, and component checks are technician work, not DIY steps.
| Source detail | What it says |
|---|---|
| Source repair action | Check the named sensor and connector first; if the connection is normal, check the indoor or inverter PCB called out by the service table. |
| Singapore / model note | Use this table only for the listed YouMe 2.0 System 5 source family until another Toshiba SG diagnostic manual is added. |
| Singapore / model note | Official Toshiba interface table for Residential AC type. Treat these as interface check-code rows and confirm the exact room-aircon model before parts diagnosis. |
What to check before repair
Use this split to separate safe evidence capture from the tests a technician should prove before quoting parts.
| You can check | Technician should confirm |
|---|---|
| Before resetting 19, take a clear display photo and blinking-light video if the unit shows one. | Confirm which sensor 19 maps to on the exact model table. |
| Capture the Toshiba indoor and outdoor model stickers so the correct family row is used. | Measure the sensor value against the service-manual resistance or voltage range. |
| Note whether one room, several rooms, or the whole system is affected, plus whether it returns after one reset. | Check connector condition, harness continuity, and PCB input before replacing boards. |
What changes the next step
These clues decide whether the first check is room-side, shared outdoor-side, refrigerant-side, source-table, or model-family confirmation.
| What you see | What it points to |
|---|---|
| Only one indoor unit shows 19. | The affected room, indoor board path, wiring route, or local component should be checked first. |
| Several rooms or the outdoor unit show the same 19 fault. | The shared outdoor side, power path, communication trunk, or refrigerant circuit needs priority checking. |
| The fault appears immediately even before the unit cools properly. | Sensor value, connector, harness, and PCB input should be tested in that order. |
| The same code appears with different meanings in the source rows. | Model family, source table, and system type decide which meaning applies before parts are quoted. |
| The model belongs to Multi-Split, Wall-Mounted Split, Single-Split rows such as YouMe 2.0 System 5 - RAS-5M51U2ACVG-SG, RAC TU2C-LINK Interface - Residential AC type. | The loaded row is source-backed by official diagnostic material. Use the matching source row before quoting parts. |
Sensor or PCB decision
Toshiba 19 is usually repair-first if a sensor or harness reading is confirmed. Board replacement should wait until the sensor circuit is tested.
Sensor replacement is usually targeted when resistance or voltage readings are out of range.
Harness or connector damage can look like a sensor fault until continuity is checked.
PCB replacement is a later step if the sensor and wiring test correctly.
Toshiba 19 questions
What does the Toshiba 19 error mean?
Can I fix a Toshiba 19 error myself?
Is it safe to keep running the aircon with a 19 error?
What causes a Toshiba 19 error?
Will a Toshiba 19 error need a repair or a full replacement?
What should I send a technician about a Toshiba 19 error?
Confirm the fault
Share the error code, model number and symptoms so we can assess the likely cause.
Not the right code?
Browse the full Toshiba list or check a few codes in the same fault category.
Ready to get started?
Tell us what’s going on. Symptoms, setup, photos, anything we should know. We’ll assess and come back with the right next step.
Read next
Use these if the quote mentions the parts, checks, or repair path this code points to.