Toshiba SMMS / SHRM VRF Aircon F03 Error Code
Use this Toshiba SMMS / SHRM VRF F03 error code guide to capture the fault correctly and see what should be checked before parts are quoted.
What does Toshiba F03 mean?
Toshiba SMMS / SHRM VRF F03 is listed as indoor heat-exchanger temperature sensor TC1 is open or shorted in mixed model-family source rows, including SHRM Advance MMY-SUG R32. The loaded row is source-backed by official diagnostic material. Confirm the exact model, series, or signal row before accepting a parts quote.
Open, shorted, displaced, or out-of-range thermistor or pressure-sensor reading.
Loose sensor connector, damaged sensor harness, or water-affected wiring.
PCB input fault after the sensor and wiring readings are confirmed.
What to do now
Use these steps before customer action, a sensor check, or PCB quote.
Treat it as a fault signal
If F03 remains displayed or cooling is still abnormal, preserve the code and arrange diagnosis.
No manufacturer reset steps listed for F03
Capture the complete F03 display and model stickers first. The selected source row lists no customer reset procedure; do not treat a generic power-cycle as manufacturer guidance.
Send these to us
F03 error code, a clear display photo, Toshiba SMMS / SHRM VRF model stickers, affected rooms, operating state when the code appeared, and when the fault appears
Source-specific guidance
These diagnostic-reference notes help match the code to the exact model. Electrical, refrigerant, wiring, resistance, and component checks are technician work, not DIY steps.
| Source detail | What it says |
|---|---|
| Diagnostic note | Record the code and subcode. A qualified technician should test the named sensor, connector, harness, and resistance against the exact SMMS service manual before replacing a PCB. |
| Diagnostic note | Record the complete code, subcode, reporting unit, and model. A qualified technician should test the named component and circuit against SVM-22072-1. |
| Singapore / model note | Official Toshiba SMMS-u MMY-MUP service evidence. Toshiba Singapore lists cooling-only MMY-MUP...T8P-SG SMMS Infinity models, while this service manual covers European MMY-MUP...HT8P-E heat-pump variants. Confirm the complete model suffix and its local service manual before diagnosis or parts replacement. |
| Singapore / model note | Official Toshiba SVM-22072-1 row for SHRM Advance MMY-SUG R32 heat-pump and heat-recovery systems. The checked manufacturer page is regional rather than a Singapore product listing, so confirm the full model suffix and locally supplied service manual before diagnosis or parts replacement. |
- Source detail
- Diagnostic note
- What it says
- Record the code and subcode. A qualified technician should test the named sensor, connector, harness, and resistance against the exact SMMS service manual before replacing a PCB.
- Source detail
- Diagnostic note
- What it says
- Record the complete code, subcode, reporting unit, and model. A qualified technician should test the named component and circuit against SVM-22072-1.
- Source detail
- Singapore / model note
- What it says
- Official Toshiba SMMS-u MMY-MUP service evidence. Toshiba Singapore lists cooling-only MMY-MUP...T8P-SG SMMS Infinity models, while this service manual covers European MMY-MUP...HT8P-E heat-pump variants. Confirm the complete model suffix and its local service manual before diagnosis or parts replacement.
- Source detail
- Singapore / model note
- What it says
- Official Toshiba SVM-22072-1 row for SHRM Advance MMY-SUG R32 heat-pump and heat-recovery systems. The checked manufacturer page is regional rather than a Singapore product listing, so confirm the full model suffix and locally supplied service manual before diagnosis or parts replacement.
What to check before repair
Use this split to separate safe evidence capture from the tests a technician should prove before quoting parts.
| You can check | Technician should confirm |
|---|---|
| Before taking any system action on F03, take a clear display photo. | Confirm which sensor F03 maps to on the exact model table. |
| Capture the Toshiba SMMS / SHRM VRF indoor and outdoor model stickers so the correct family row is used. | Measure the sensor value against the service-manual resistance or voltage range. |
| The selected source row lists no customer reset procedure. Note whether one room, several rooms, or the whole system is affected. | Check connector condition, harness continuity, and PCB input before replacing boards. |
- You can check
- Before taking any system action on F03, take a clear display photo.
- Technician should confirm
- Confirm which sensor F03 maps to on the exact model table.
- You can check
- Capture the Toshiba SMMS / SHRM VRF indoor and outdoor model stickers so the correct family row is used.
- Technician should confirm
- Measure the sensor value against the service-manual resistance or voltage range.
- You can check
- The selected source row lists no customer reset procedure. Note whether one room, several rooms, or the whole system is affected.
- Technician should confirm
- Check connector condition, harness continuity, and PCB input before replacing boards.
What changes the next step
These clues decide whether the first check is room-side, shared outdoor-side, refrigerant-side, source-table, or model-family confirmation.
| What you see | What it points to |
|---|---|
| Only one indoor unit shows F03. | The affected room, indoor board path, wiring route, or local component should be checked first. |
| Several rooms or the outdoor unit show the same F03 fault. | Prioritise the reporting-unit sensor circuit, shared harness path, and control-board input. |
| The fault appears immediately even before the unit cools properly. | Sensor value, connector, harness, and PCB input should be tested in that order. |
| The model family is different from the row you found online. | Use the model or series filter first; same-looking codes can still belong to different diagnostic tables. |
| The model belongs to mixed model-family source rows, including SHRM Advance MMY-SUG R32. | The loaded row is source-backed by official diagnostic material. Use the matching source row before quoting parts. |
- What you see
- Only one indoor unit shows F03.
- What it points to
- The affected room, indoor board path, wiring route, or local component should be checked first.
- What you see
- Several rooms or the outdoor unit show the same F03 fault.
- What it points to
- Prioritise the reporting-unit sensor circuit, shared harness path, and control-board input.
- What you see
- The fault appears immediately even before the unit cools properly.
- What it points to
- Sensor value, connector, harness, and PCB input should be tested in that order.
- What you see
- The model family is different from the row you found online.
- What it points to
- Use the model or series filter first; same-looking codes can still belong to different diagnostic tables.
- What you see
- The model belongs to mixed model-family source rows, including SHRM Advance MMY-SUG R32.
- What it points to
- The loaded row is source-backed by official diagnostic material. Use the matching source row before quoting parts.
Sensor or PCB decision
Toshiba SMMS / SHRM VRF F03 is usually repair-first if a sensor or harness reading is confirmed. Board replacement should wait until the sensor circuit is tested.
Sensor replacement is usually targeted when resistance or voltage readings are out of range.
Harness or connector damage can look like a sensor fault until continuity is checked.
PCB replacement is a later step if the sensor and wiring test correctly.
Toshiba F03 questions
What does the Toshiba F03 error mean?
Can I fix a Toshiba F03 error myself?
Is it safe to keep running the aircon with an F03 error?
What causes a Toshiba F03 error?
Will a Toshiba F03 error need a repair or a full replacement?
What should I send a technician about a Toshiba F03 error?
Confirm the fault
Share the error code, model number and symptoms so we can assess the likely cause.
Not the right code?
Browse the full Toshiba list or check a few codes in the same fault category.
Ready to get started?
Tell us what’s going on. Symptoms, setup, photos, anything we should know. We’ll assess and come back with the right next step.
Read next
Use these if the quote mentions the parts, checks, or repair path this code points to.