Haier Aircon 19 Error Code & Blinking Light
Use this Haier 19 guide to confirm the source table meaning, capture the reporting equipment and model, and match the service manual before diagnosis. Match the model first; same-looking signals can point to different rows.
What does Haier 19 mean?
Haier 19 is listed as DC-bus or AC input undervoltage protection, compressor overcurrent detected by the control board, and PWM module circuit-selection failure in S2 R32 split-system outdoor unit, FlexFit Pro large cassette, 2024 1U71 S2 SG / SR outdoor units, and 2024 1U90-1U160 S2 outdoor units source rows. The loaded row is source-backed by official diagnostic material. Do not collapse this code across model families; use the model, series, or system type to choose the right row. Confirm the exact model, series, or signal row before accepting a parts quote.
Choose the matching source row
The same visible code has more than one source-backed meaning. Match the model family, system type, or reporting unit before approving parts.
| Code | What it means | What to check first |
|---|---|---|
| S2 R32 split-system outdoor unit / 2024 1U90-1U160 S2 outdoor units | DC-bus or AC input undervoltage protection | Match this row to the installed model or reporting unit, then use the source-specific checks below. |
| FlexFit Pro large cassette | Compressor overcurrent detected by the control board | Match this row to the installed model or reporting unit, then use the source-specific checks below. |
| 2024 1U71 S2 SG / SR outdoor units | PWM module circuit-selection failure. Shown as: outdoor PCB LED: 19 flashes. | Match this row to the installed model or reporting unit, then use the source-specific checks below. |
- Code
- S2 R32 split-system outdoor unit / 2024 1U90-1U160 S2 outdoor units
- What it means
- DC-bus or AC input undervoltage protection
- What to check first
- Match this row to the installed model or reporting unit, then use the source-specific checks below.
- Code
- FlexFit Pro large cassette
- What it means
- Compressor overcurrent detected by the control board
- What to check first
- Match this row to the installed model or reporting unit, then use the source-specific checks below.
- Code
- 2024 1U71 S2 SG / SR outdoor units
- What it means
- PWM module circuit-selection failure. Shown as: outdoor PCB LED: 19 flashes.
- What to check first
- Match this row to the installed model or reporting unit, then use the source-specific checks below.
How this fault may be shown
Match every scope item the source provides—exact model where listed, PCB or panel where listed, and reporting device—before using a displayed value. These manufacturer crosswalks are display evidence, not universal codes or repair instructions.
Split outdoor control board - 1U105 SSModels 1U105S2SS1FA, 1U105S2SS2FA · Haier Split and Multi Split Error Codes, version 01/2024, PDF page 20
| Reported by | Shown as | Source meaning |
|---|---|---|
| Outdoor control-board diagnostic display | 19 | AC or DC voltage too low |
- Reported by
- Outdoor control-board diagnostic display
- Shown as
- 19
- Source meaning
- AC or DC voltage too low
Split outdoor control board - 1U125 SN / 1U140 SPModels 1U125S2SN1FA, 1U125S2SN1FB, 1U140S2SP1FA, 1U140S2SP1FB · Haier Split and Multi Split Error Codes, version 01/2024, PDF page 20
| Reported by | Shown as | Source meaning |
|---|---|---|
| Outdoor control-board diagnostic display | 19 | AC or DC voltage too low |
- Reported by
- Outdoor control-board diagnostic display
- Shown as
- 19
- Source meaning
- AC or DC voltage too low
Split outdoor control board - 1U71 SG / SRModels 1U71S2SG1FA, 1U71S2SR2FA · Haier Split and Multi Split Error Codes, version 01/2024, PDF page 20
| Reported by | Shown as | Source meaning |
|---|---|---|
| Outdoor control-board diagnostic display | 19 | PWM module circuit failure |
- Reported by
- Outdoor control-board diagnostic display
- Shown as
- 19
- Source meaning
- PWM module circuit failure
Low-static duct PCB 0151800267 LED4 / LED3PCB 0151800267 · Haier Split and Multi Split Error Codes, version 01/2024, PDF page 21
| Reported by | Shown as | Source meaning |
|---|---|---|
| Low-static duct TIMER LED4 and RUNNING LED3 | LED4 3 / LED3 9 | AC or DC voltage too low |
| Low-static duct TIMER LED4 and RUNNING LED3 | LED4 3 / LED3 9 | PWM module circuit failure |
- Reported by
- Low-static duct TIMER LED4 and RUNNING LED3
- Shown as
- LED4 3 / LED3 9
- Source meaning
- AC or DC voltage too low
- Reported by
- Low-static duct TIMER LED4 and RUNNING LED3
- Shown as
- LED4 3 / LED3 9
- Source meaning
- PWM module circuit failure
Low/medium-static duct PCB 0151800644 LED4 / LED3PCB 0151800644 · Haier Split and Multi Split Error Codes, version 01/2024, PDF page 21
| Reported by | Shown as | Source meaning |
|---|---|---|
| Low/medium-static duct TIMER LED4 and RUNNING LED3 | LED4 3 / LED3 9 | AC or DC voltage too low |
| Low/medium-static duct TIMER LED4 and RUNNING LED3 | LED4 3 / LED3 9 | PWM module circuit failure |
- Reported by
- Low/medium-static duct TIMER LED4 and RUNNING LED3
- Shown as
- LED4 3 / LED3 9
- Source meaning
- AC or DC voltage too low
- Reported by
- Low/medium-static duct TIMER LED4 and RUNNING LED3
- Shown as
- LED4 3 / LED3 9
- Source meaning
- PWM module circuit failure
Low/medium-static duct panel on PCB 0151800644PCB 0151800644 · Panels P1B-890IA/D, P1B-1210IA/D · Haier Split and Multi Split Error Codes, version 01/2024, PDF page 21
| Reported by | Shown as | Source meaning |
|---|---|---|
| Low/medium-static duct panel display | F19 | AC or DC voltage too low |
| Low/medium-static duct panel display | F19 | PWM module circuit failure |
- Reported by
- Low/medium-static duct panel display
- Shown as
- F19
- Source meaning
- AC or DC voltage too low
- Reported by
- Low/medium-static duct panel display
- Shown as
- F19
- Source meaning
- PWM module circuit failure
AC ceiling/floor TIMER LED6 / RUNNING LED1Models AC35S2SG1FA, AC50S2SG1FA, AC71S2SG1FA, AC90S2SH1FA, AC105S2SH1FA, AC125S2SK1FA, AC140S2SK1FA, AC160S2SK1FA · Haier Split and Multi Split Error Codes, version 01/2024, PDF page 23
| Reported by | Shown as | Source meaning |
|---|---|---|
| AC ceiling/floor TIMER LED6 and RUNNING LED1 | LED6 3 / LED1 9 | AC or DC voltage too low |
| AC ceiling/floor TIMER LED6 and RUNNING LED1 | LED6 3 / LED1 9 | PWM module circuit failure |
- Reported by
- AC ceiling/floor TIMER LED6 and RUNNING LED1
- Shown as
- LED6 3 / LED1 9
- Source meaning
- AC or DC voltage too low
- Reported by
- AC ceiling/floor TIMER LED6 and RUNNING LED1
- Shown as
- LED6 3 / LED1 9
- Source meaning
- PWM module circuit failure
AC ceiling/floor displayModels AC35S2SG1FA, AC50S2SG1FA, AC71S2SG1FA, AC90S2SH1FA, AC105S2SH1FA, AC125S2SK1FA, AC140S2SK1FA, AC160S2SK1FA · Haier Split and Multi Split Error Codes, version 01/2024, PDF page 23
| Reported by | Shown as | Source meaning |
|---|---|---|
| AC ceiling/floor display | F19 | AC or DC voltage too low |
| AC ceiling/floor display | F19 | PWM module circuit failure |
- Reported by
- AC ceiling/floor display
- Shown as
- F19
- Source meaning
- AC or DC voltage too low
- Reported by
- AC ceiling/floor display
- Shown as
- F19
- Source meaning
- PWM module circuit failure
AF floor TIMER LED6 / RUNNING LED1Models AF25S2SD1FA, AF35S2SD1FA, AF42S2SD1FA · Haier Split and Multi Split Error Codes, version 01/2024, PDF page 24
| Reported by | Shown as | Source meaning |
|---|---|---|
| AF floor TIMER LED6 and RUNNING LED1 | LED6 3 / LED1 9 | AC or DC voltage too low |
| AF floor TIMER LED6 and RUNNING LED1 | LED6 3 / LED1 9 | PWM module circuit failure |
- Reported by
- AF floor TIMER LED6 and RUNNING LED1
- Shown as
- LED6 3 / LED1 9
- Source meaning
- AC or DC voltage too low
- Reported by
- AF floor TIMER LED6 and RUNNING LED1
- Shown as
- LED6 3 / LED1 9
- Source meaning
- PWM module circuit failure
AF floor displayModels AF25S2SD1FA, AF35S2SD1FA, AF42S2SD1FA · Haier Split and Multi Split Error Codes, version 01/2024, PDF page 24
| Reported by | Shown as | Source meaning |
|---|---|---|
| AF floor display | F19 | AC or DC voltage too low |
| AF floor display | F19 | PWM module circuit failure |
- Reported by
- AF floor display
- Shown as
- F19
- Source meaning
- AC or DC voltage too low
- Reported by
- AF floor display
- Shown as
- F19
- Source meaning
- PWM module circuit failure
Source-labelled cassette TIMER / RUNNING LEDsSource-labelled equipment family; exact models are not listed in this table · Haier Split and Multi Split Error Codes, version 01/2024, PDF page 25
| Reported by | Shown as | Source meaning |
|---|---|---|
| Cassette TIMER and RUNNING LEDs | TIMER 3 / RUNNING 9 | AC or DC voltage too low |
| Cassette TIMER and RUNNING LEDs | TIMER 3 / RUNNING 9 | PWM module circuit failure |
- Reported by
- Cassette TIMER and RUNNING LEDs
- Shown as
- TIMER 3 / RUNNING 9
- Source meaning
- AC or DC voltage too low
- Reported by
- Cassette TIMER and RUNNING LEDs
- Shown as
- TIMER 3 / RUNNING 9
- Source meaning
- PWM module circuit failure
Source-labelled cassette displaySource-labelled equipment family; exact models are not listed in this table · Haier Split and Multi Split Error Codes, version 01/2024, PDF page 25
| Reported by | Shown as | Source meaning |
|---|---|---|
| Cassette display | 27 | AC or DC voltage too low |
| Cassette display | 27 | PWM module circuit failure |
- Reported by
- Cassette display
- Shown as
- 27
- Source meaning
- AC or DC voltage too low
- Reported by
- Cassette display
- Shown as
- 27
- Source meaning
- PWM module circuit failure
What to do now
Use these steps to record evidence and match the installed model to its service manual before diagnosis or a repair quote.
Record 19 and match the service manual
Record 19 and stop there; the source table gives no customer reset procedure. Arrange diagnosis with the matching service manual.
No manufacturer reset steps listed for 19
Capture the complete 19 error code and blinking light and model stickers first. The source table lists the meaning but no customer reset procedure; do not treat a generic power-cycle as manufacturer guidance.
Send these to us
19 error code and blinking light, a clear display photo and blinking-light video if the unit shows one, Haier indoor and outdoor model stickers, the controller, gateway, or unit that reported the code, operating mode and affected area, and any power or setting changes made after the code appeared
Source-specific guidance
These diagnostic-reference notes help match the code to the exact model. Electrical, refrigerant, wiring, resistance, and component checks are technician work, not DIY steps.
| Source detail | What it says |
|---|---|
| Singapore / model note | Official Haier Australia S2 split-system manual row. Confirm the exact 1U S2 outdoor model before using the meaning; no universal Haier-model parity is claimed. |
| Singapore / model note | Official Haier Appliances FlexFit Pro large-cassette display decoder. The source converts an outdoor decimal fault to the hexadecimal code flashed indoors; the exact display identity is retained. Match the named model family before diagnosis. |
| Singapore / model note | Regional manufacturer handbook, PDF page 11. Confirm the exact listed model and reporting display; this meaning is not claimed for every Haier system. |
- Source detail
- Singapore / model note
- What it says
- Official Haier Australia S2 split-system manual row. Confirm the exact 1U S2 outdoor model before using the meaning; no universal Haier-model parity is claimed.
- Source detail
- Singapore / model note
- What it says
- Official Haier Appliances FlexFit Pro large-cassette display decoder. The source converts an outdoor decimal fault to the hexadecimal code flashed indoors; the exact display identity is retained. Match the named model family before diagnosis.
- Source detail
- Singapore / model note
- What it says
- Regional manufacturer handbook, PDF page 11. Confirm the exact listed model and reporting display; this meaning is not claimed for every Haier system.
What to check before repair
The source table establishes the code meaning, not a repair procedure. Capture evidence first; model-specific tests belong to the matching service manual.
| You can check | Technician should confirm |
|---|---|
| Photograph the complete 19 error code and blinking light before taking any action. | Confirm 19 exactly and record which controller, gateway, or unit reported it. |
| Capture the Haier indoor and outdoor model stickers and identify which controller or unit reported it. | Match the indoor and outdoor model stickers, installed family, and reporting equipment to the source scope. |
| The source table provides no customer reset procedure. Preserve the evidence and use the matching service manual for any system action. | Follow the matching service-manual procedure and keep measured test evidence before naming a failed part. |
- You can check
- Photograph the complete 19 error code and blinking light before taking any action.
- Technician should confirm
- Confirm 19 exactly and record which controller, gateway, or unit reported it.
- You can check
- Capture the Haier indoor and outdoor model stickers and identify which controller or unit reported it.
- Technician should confirm
- Match the indoor and outdoor model stickers, installed family, and reporting equipment to the source scope.
- You can check
- The source table provides no customer reset procedure. Preserve the evidence and use the matching service manual for any system action.
- Technician should confirm
- Follow the matching service-manual procedure and keep measured test evidence before naming a failed part.
Source-bounded repair decision
Haier 19 confirms the source-table fault label, not a failed part or repair procedure. Match the installed model to its service manual and require measured diagnostic evidence before approving parts, settings, or refrigerant work.
Whether the reporting controller or unit and exact installed model are confirmed.
What the matching service-manual procedure and measured tests show.
Whether the proposed repair names the evidence for the failed part or condition.
Haier 19 questions
What does the Haier 19 error mean?
Haier 19 is listed as DC-bus or AC input undervoltage protection, compressor overcurrent detected by the control board, and PWM module circuit-selection failure in S2 R32 split-system outdoor unit, FlexFit Pro large cassette, 2024 1U71 S2 SG / SR outdoor units, and 2024 1U90-1U160 S2 outdoor units source rows. The loaded row is source-backed by official diagnostic material. Do not collapse this code across model families; use the model, series, or system type to choose the right row. Confirm the exact model, series, or signal row before accepting a parts quote.
Can I fix a Haier 19 error myself?
No. 19 needs a technician's measurement before parts are decided. Photograph the complete 19 error code and blinking light before taking any action. Capture the Haier indoor and outdoor model stickers and identify which controller or unit reported it.
Is it safe to keep running the aircon with a 19 error?
Record 19 and stop there; the source table gives no customer reset procedure. Arrange diagnosis with the matching service manual.
What causes a Haier 19 error?
Haier 19 has source-backed wording that depends on the exact model, source row, or reporting unit. Use the decoder on this page before assuming a specific cause.
Will a Haier 19 error need a repair or a full replacement?
Haier 19 confirms the source-table fault label, not a failed part or repair procedure. Match the installed model to its service manual and require measured diagnostic evidence before approving parts, settings, or refrigerant work.
What should I send a technician about a Haier 19 error?
Before booking, send: 19 error code and blinking light, a clear display photo and blinking-light video if the unit shows one, Haier indoor and outdoor model stickers, the controller, gateway, or unit that reported the code, operating mode and affected area, and any power or setting changes made after the code appeared.
Confirm the fault
Share the error code, model number and symptoms so we can assess the likely cause.
Not the right code?
Browse the full Haier list or check a few codes in the same fault category.
Ready to get started?
Tell us what’s going on. Symptoms, setup, photos, anything we should know. We’ll assess and come back with the right next step.
Read next
Use this quote-check guide only after the matching service manual identifies the diagnostic path.