Mitsubishi Electric aircon 16 / LED1 10x, LED2 off blinking light
Use this Mitsubishi Electric 16 / LED1 10x, LED2 off blinking light guide to decide when to stop resetting, what to capture, and what to check before parts are quoted.
What does Mitsubishi Electric 16 / LED1 10x, LED2 off mean?
Mitsubishi Electric 16 / LED1 10x, LED2 off is listed as compressor in Multi-Split rows such as FP Series, Starmex R32. The loaded row is source-backed by official diagnostic material. Confirm the exact model, series, or signal row before accepting a parts quote.
Compressor start, lock, overcurrent, overload, or inverter-drive protection.
Power-module, IPM, voltage, or wiring fault affecting compressor drive.
Compressor mechanical or winding issue after electrical checks are confirmed.
What to do now
Use these steps before another reset or parts quote.
Stop using the unit if 16 / LED1 10x, LED2 off returns
Stop repeated restarts if 16 / LED1 10x, LED2 off returns; compressor and inverter faults can become more expensive when forced to run.
Reset 16 / LED1 10x, LED2 off once
Capture the 16 / LED1 10x, LED2 off pattern, then reset once only if there is no burning smell, repeated trip, or hot outdoor unit.
Send these to us
16 / LED1 10x, LED2 off blinking light, a short video of the blinking-light sequence, Mitsubishi Electric model stickers, affected rooms, reset result, and trip timing and outdoor-unit behaviour
Source-specific guidance
These diagnostic-reference notes help match the code to the exact model. Electrical, refrigerant, wiring, resistance, and component checks are technician work, not DIY steps.
| Source detail | What it says |
|---|---|
| Source repair action | Do not keep resetting the system if this pattern returns. Record the model number, lamp or LED pattern, and affected rooms before booking diagnosis. |
| Singapore / model note | Official Mitsubishi Electric checklist action: Reconnect compressor connector, check inverter or compressor, and check stop valve. |
What to check before repair
Use this split to separate safe evidence capture from the tests a technician should prove before quoting parts.
| You can check | Technician should confirm |
|---|---|
| Before resetting 16 / LED1 10x, LED2 off, take a short video of the blinking-light sequence. | Confirm whether 16 / LED1 10x, LED2 off is compressor start, overload, lock, or drive protection. |
| Capture the Mitsubishi Electric indoor and outdoor model stickers so the correct family row is used. | Check supply voltage, inverter output, IPM status, compressor current, and winding readings. |
| Note whether one room, several rooms, or the whole system is affected, plus whether it returns after one reset. | Review trip history and compressor mechanical signs before quoting replacement. |
What changes the next step
These clues decide whether the first check is room-side, shared outdoor-side, refrigerant-side, source-table, or model-family confirmation.
| What you see | What it points to |
|---|---|
| Only one indoor unit shows 16 / LED1 10x, LED2 off. | The affected room, indoor board path, wiring route, or local component should be checked first. |
| Several rooms or the outdoor unit show the same 16 / LED1 10x, LED2 off fault. | The shared outdoor side, power path, communication trunk, or refrigerant circuit needs priority checking. |
| The outdoor unit hums, starts briefly, or trips soon after startup. | Power, inverter, IPM, compressor current, and winding checks decide the repair path. |
| The model family is different from the row you found online. | Use the model or series filter first; same-looking codes can still belong to different diagnostic tables. |
| The model belongs to Multi-Split rows such as FP Series, Starmex R32. | The loaded row is source-backed by official diagnostic material. Use the matching source row before quoting parts. |
Compressor drive or replacement decision
Mitsubishi Electric 16 / LED1 10x, LED2 off can still be a repair if power, inverter, or module checks find the cause. Compressor replacement should be weighed against age, warranty, and the rest of the system condition.
Inverter or IPM faults are not the same as confirmed compressor mechanical failure.
Compressor winding and current readings should be measured before replacement is discussed.
Older systems need a repair-versus-replace check if compressor-side parts are expensive.
Mitsubishi Electric 16 / LED1 10x, LED2 off questions
What does the Mitsubishi Electric 16 / LED1 10x, LED2 off error mean?
Can I fix a Mitsubishi Electric 16 / LED1 10x, LED2 off error myself?
Is it safe to keep running the aircon with a 16 / LED1 10x, LED2 off error?
What causes a Mitsubishi Electric 16 / LED1 10x, LED2 off error?
Will a Mitsubishi Electric 16 / LED1 10x, LED2 off error need a repair or a full replacement?
What should I send a technician about a Mitsubishi Electric 16 / LED1 10x, LED2 off error?
Confirm the fault
Share the error code, model number and symptoms so we can assess the likely cause.
Not the right code?
Browse the full Mitsubishi Electric list or check a few codes in the same fault category.
Ready to get started?
Tell us what’s going on. Symptoms, setup, photos, anything we should know. We’ll assess and come back with the right next step.
Read next
Use these if the quote mentions the parts, checks, or repair path this code points to.