Skip to main content

Midea Aircon Not Cold: The Usual Causes and the Repair

A Midea split that runs without cooling usually starts with a dirty filter or coil, a choked outdoor unit, or too little refrigerant from a leak. Midea's service tables also name sensor and compressor faults, and several of those show as a display code.

On this page

Why is my Midea aircon not cold?

Midea's service manual for its Xtreme ONOFF wall units, a fixed-speed range sold in Thailand, lists a dirty air filter, a dirty indoor coil and a dirty or partly blocked outdoor condenser as causes of weak cooling. It also lists a refrigerant shortage, a restricted liquid line, an inefficient compressor and a unit too small for its heat load.

The same manual names settings that look like a fault: fan mode, a set temperature above the room's, and the Silence function left on. Causes shared by every brand sit on the aircon not cold page.

Why is my Midea aircon not cold? summary table
Cause in Midea's tableWhat it looks likeWho deals with it
Fan mode, high set temperature or Silence onAir moves but stays warmChange the setting on the remote
Dirty air filter or indoor coilWeak airflow from the indoor unitServicing
Dirty or blocked outdoor condenserOutdoor unit fins clogged or boxed inServicing, clearing the airflow
Refrigerant shortageEL 0C on some models, cooling fadesLeak test, seal, then recharge
Sensor or compressor faultA code such as EH 61 or PC 04Diagnosis and part replacement
Unit too small for the loadNever reaches the set temperatureSizing check

What to check first

Start with the remote: cooling mode, a set temperature below the room's, and Silence off. Close windows and doors, since extra heat load is on Midea's list.

Then note whatever the indoor display shows and how long cooling has been weak. A filter or coil that needs cleaning is a servicing job, so leave the panels and the outdoor unit closed.

Which Midea codes point to gas, sensors or the compressor?

On Midea's Glory Pro wall inverters, as listed in Midea Malaysia's catalogue, EL 0C means refrigerant leakage detection, or the system lacks refrigerant. Midea's quick fix is to check for a gas leak, the copper pipe flare nuts and the indoor board.

EH 60 and EH 61 flag the indoor room and coil temperature sensors, called thermistors. EC 52, EC 53 and EC 54 flag the outdoor sensors.

PC 02 covers discharge temperature, inverter module or high pressure protection, and Midea's check includes gas pressure and system blockage. PC 04 is an inverter compressor drive error. Codes differ by series, so the Midea blinking light guide covers reading them on other models.

Repair or replace a Midea that has stopped cooling

Midea Singapore's warranty applies only to units registered online within 14 days of purchase, held by the original owner and used in homes. It excludes regular cleaning, general service and overhaul, and any repair or dismantling by others before Midea approves it.

So a covered unit with a part fault goes to Midea first, while a dirty coil is a servicing cost either way. The Midea aircon warranty guide sets out the rest of the terms.

Outside warranty, sensors, boards and joint leaks are normally worth fixing. Failed boards are replaced, and gas goes back in only after the leaking joint or pipe is sealed.

NEA's register lists 11 Midea single-phase VRF entries alongside 58 single and multi-split entries. Among VRF brands, Snowflake Aircon Services repairs Daikin VRV only, so a Midea VRF that stops cooling gets servicing here, not repair.

A compressor fault on an older system is the case for pricing a replacement. For a Midea showing EL 0C, a diagnostic visit tests for the leak first.

Common questions

Why is my Midea aircon running but not cold?
Midea's service manual lists a dirty air filter or indoor coil, a blocked outdoor condenser, low refrigerant, a restricted liquid line, a weak compressor and an undersized unit. Fan mode, a high set temperature and the Silence function also leave a Midea blowing air that is not cold.
What does EL 0C mean on a Midea aircon?
On Midea Glory Pro wall inverters, EL 0C means refrigerant leakage detection, or the system lacks refrigerant. Midea's listed checks are a gas leak, the copper pipe flare nuts and the indoor board, so a technician tests for the leak before any gas is added.
Does the Midea warranty cover a unit that is not cooling?
Midea Singapore's warranty covers registered units only: registered online within 14 days, owned by the original buyer and in domestic use. Cleaning, general service and overhaul are excluded, so a clogged coil is not covered, and a repair by others before Midea approves it falls outside the terms.
Is a Midea aircon worth repairing when it stops cooling?
A Midea with a sensor fault or a joint leak is normally worth repairing, and a failed board is replaced with a new one. A failed compressor on an older system is the case for pricing a replacement, because the coils, fan motors and boards around it are the same age.

Sources