Mitsubishi Electric Aircon 17 / LED1 5x, LED2 Off
Use this Mitsubishi Electric 17 / LED1 5x, LED2 off blinking light guide to capture the fault correctly and see what should be checked before parts are quoted.
What does Mitsubishi Electric 17 / LED1 5x, LED2 off mean?
Mitsubishi Electric 17 / LED1 5x, LED2 off is listed as high pressure protection or thermal protector protection in Multi-Split rows such as FP Series, Starmex R32. The loaded row is source-backed by official diagnostic material. Confirm the exact model, series, or signal row before accepting a parts quote.
Low refrigerant, active leak, restriction, or abnormal pressure reading.
Dirty condenser, weak outdoor fan, blocked airflow, or high-load operation.
Pressure sensor, expansion path, or compressor protection after readings are taken.
What to do now
Use these steps before customer action, gas work, a pressure check, or parts quote.
Stop using the unit if 17 / LED1 5x, LED2 off returns
Stop using the unit if 17 / LED1 5x, LED2 off returns with weak cooling, frost, hissing, or outdoor-unit tripping.
No manufacturer reset steps listed for 17 / LED1 5x, LED2 off
Capture the complete 17 / LED1 5x, LED2 off pattern and model stickers first. The selected source row lists no customer reset procedure; do not treat a generic power-cycle as manufacturer guidance.
Send these to us
17 / LED1 5x, LED2 off blinking light, a short video of the blinking-light sequence, Mitsubishi Electric model stickers, affected rooms, operating state when the code appeared, and cooling-loss timeline and any recent gas top-up
Source-specific guidance
These diagnostic-reference notes help match the code to the exact model. Electrical, refrigerant, wiring, resistance, and component checks are technician work, not DIY steps.
| Source detail | What it says |
|---|---|
| Diagnostic note | Do not keep resetting the system if this pattern returns. Record the model number, lamp or LED pattern, and affected rooms before booking diagnosis. |
| Singapore / model note | Official Mitsubishi Electric checklist action: Check refrigerant circuit, stop valve, short-cycling airflow, high pressure switch, thermal protector, thermistor connection, refrigerant leak, and locked compressor. |
- Source detail
- Diagnostic note
- What it says
- Do not keep resetting the system if this pattern returns. Record the model number, lamp or LED pattern, and affected rooms before booking diagnosis.
- Source detail
- Singapore / model note
- What it says
- Official Mitsubishi Electric checklist action: Check refrigerant circuit, stop valve, short-cycling airflow, high pressure switch, thermal protector, thermistor connection, refrigerant leak, and locked compressor.
What to check before repair
Use this split to separate safe evidence capture from the tests a technician should prove before quoting parts.
| You can check | Technician should confirm |
|---|---|
| Before taking any system action on 17 / LED1 5x, LED2 off, take a short video of the blinking-light sequence. | Match 17 / LED1 5x, LED2 off to low-pressure, high-pressure, leak, or refrigerant-cycle protection. |
| Capture the Mitsubishi Electric indoor and outdoor model stickers so the correct family row is used. | Measure operating pressures, coil temperatures, airflow, and outdoor fan condition. |
| The selected source row lists no customer reset procedure. Note whether one room, several rooms, or the whole system is affected. | Leak-check or pressure-test before recommending another refrigerant top-up. |
- You can check
- Before taking any system action on 17 / LED1 5x, LED2 off, take a short video of the blinking-light sequence.
- Technician should confirm
- Match 17 / LED1 5x, LED2 off to low-pressure, high-pressure, leak, or refrigerant-cycle protection.
- You can check
- Capture the Mitsubishi Electric indoor and outdoor model stickers so the correct family row is used.
- Technician should confirm
- Measure operating pressures, coil temperatures, airflow, and outdoor fan condition.
- You can check
- The selected source row lists no customer reset procedure. Note whether one room, several rooms, or the whole system is affected.
- Technician should confirm
- Leak-check or pressure-test before recommending another refrigerant top-up.
What changes the next step
These clues decide whether the first check is room-side, shared outdoor-side, refrigerant-side, source-table, or model-family confirmation.
| What you see | What it points to |
|---|---|
| Only one indoor unit shows 17 / LED1 5x, LED2 off. | The affected room, indoor board path, wiring route, or local component should be checked first. |
| Several rooms or the outdoor unit show the same 17 / LED1 5x, LED2 off fault. | Prioritise the shared outdoor side, pressure conditions, airflow, and refrigerant circuit. |
| Cooling is weak, frost appears, or the outdoor unit trips under load. | Pressure, airflow, leak, and condenser checks should come before another top-up. |
| The model family is different from the row you found online. | Use the model or series filter first; same-looking codes can still belong to different diagnostic tables. |
| The model belongs to Multi-Split rows such as FP Series, Starmex R32. | The loaded row is source-backed by official diagnostic material. Use the matching source row before quoting parts. |
- What you see
- Only one indoor unit shows 17 / LED1 5x, LED2 off.
- What it points to
- The affected room, indoor board path, wiring route, or local component should be checked first.
- What you see
- Several rooms or the outdoor unit show the same 17 / LED1 5x, LED2 off fault.
- What it points to
- Prioritise the shared outdoor side, pressure conditions, airflow, and refrigerant circuit.
- What you see
- Cooling is weak, frost appears, or the outdoor unit trips under load.
- What it points to
- Pressure, airflow, leak, and condenser checks should come before another top-up.
- What you see
- The model family is different from the row you found online.
- What it points to
- Use the model or series filter first; same-looking codes can still belong to different diagnostic tables.
- What you see
- The model belongs to Multi-Split rows such as FP Series, Starmex R32.
- What it points to
- The loaded row is source-backed by official diagnostic material. Use the matching source row before quoting parts.
Pressure, leak, or airflow decision
Mitsubishi Electric 17 / LED1 5x, LED2 off needs measured pressure, airflow, and leak evidence before gas work is approved. Replacement only becomes serious when the leak, compressor, or coil repair is uneconomical.
A top-up alone is poor value if the leak source is not found.
High-pressure faults often come from airflow, condenser, fan, or overcharge conditions.
Coil leaks or compressor-related findings can shift older systems toward replacement.
Mitsubishi Electric 17 / LED1 5x, LED2 off questions
What does the Mitsubishi Electric 17 / LED1 5x, LED2 off error mean?
Can I fix a Mitsubishi Electric 17 / LED1 5x, LED2 off error myself?
Is it safe to keep running the aircon with a 17 / LED1 5x, LED2 off error?
What causes a Mitsubishi Electric 17 / LED1 5x, LED2 off error?
Will a Mitsubishi Electric 17 / LED1 5x, LED2 off error need a repair or a full replacement?
What should I send a technician about a Mitsubishi Electric 17 / LED1 5x, LED2 off error?
Confirm the fault
Share the error code, model number and symptoms so we can assess the likely cause.
Not the right code?
Browse the full Mitsubishi Electric list or check a few codes in the same fault category.
Ready to get started?
Tell us what’s going on. Symptoms, setup, photos, anything we should know. We’ll assess and come back with the right next step.
Read next
Use these if the quote mentions the parts, checks, or repair path this code points to.