Mitsubishi Heavy aircon E35 error code & blinking light
Use this Mitsubishi Heavy E35 guide to decide when to stop resetting, what to capture, and what to check before parts are quoted.
What does Mitsubishi Heavy E35 mean?
Mitsubishi Heavy E35 is listed as cooling high pressure protection in Inverter Split, Multi-Split rows such as Singapore Rocket YYS single split, SRK-YYS indoor with SRC-YYS outdoor. The loaded row is source-backed by official diagnostic material. Confirm the exact model, series, or signal row before accepting a parts quote.
Open, shorted, displaced, or out-of-range thermistor or pressure-sensor reading.
Loose sensor connector, damaged sensor harness, or water-affected wiring.
PCB input fault after the sensor and wiring readings are confirmed.
What to do now
Use these steps before another reset, sensor check, or PCB quote.
Treat it as a fault signal
If E35 returns or cooling is still abnormal, stop treating it as a simple reset issue.
Reset E35 once
Capture the E35 pattern first, then power-cycle once only and note whether the same fault returns.
Send these to us
E35 error code and blinking light, a clear display photo and blinking-light video if the unit shows one, Mitsubishi Heavy model stickers, affected rooms, reset result, and when the fault appears
Source-specific guidance
These diagnostic-reference notes help match the code to the exact model. Electrical, refrigerant, wiring, resistance, and component checks are technician work, not DIY steps.
| Source detail | What it says |
|---|---|
| Source repair action | Record the exact E-code and whether it came from the indoor display, wired remote, or outdoor PCB, then arrange diagnosis by a qualified Mitsubishi Heavy Industries technician. |
| Singapore / model note | Singapore Rocket YYS model family is from the Mitsubishi Heavy Industries Aircon Singapore residential page and RAC catalogue. Fault rows are from the official MHI RAC single-split indication table; no exact public Singapore YYS fault manual was found. |
What to check before repair
Use this split to separate safe evidence capture from the tests a technician should prove before quoting parts.
| You can check | Technician should confirm |
|---|---|
| Before resetting E35, take a clear display photo and blinking-light video if the unit shows one. | Confirm which sensor E35 maps to on the exact model table. |
| Capture the Mitsubishi Heavy indoor and outdoor model stickers so the correct family row is used. | Measure the sensor value against the service-manual resistance or voltage range. |
| Note whether one room, several rooms, or the whole system is affected, plus whether it returns after one reset. | Check connector condition, harness continuity, and PCB input before replacing boards. |
What changes the next step
These clues decide whether the first check is room-side, shared outdoor-side, refrigerant-side, source-table, or model-family confirmation.
| What you see | What it points to |
|---|---|
| Only one indoor unit shows E35. | The affected room, indoor board path, wiring route, or local component should be checked first. |
| Several rooms or the outdoor unit show the same E35 fault. | The shared outdoor side, power path, communication trunk, or refrigerant circuit needs priority checking. |
| The fault appears immediately even before the unit cools properly. | Sensor value, connector, harness, and PCB input should be tested in that order. |
| The model family is different from the row you found online. | Use the model or series filter first; same-looking codes can still belong to different diagnostic tables. |
| The model belongs to Inverter Split, Multi-Split rows such as Singapore Rocket YYS single split, SRK-YYS indoor with SRC-YYS outdoor. | The loaded row is source-backed by official diagnostic material. Use the matching source row before quoting parts. |
Sensor or PCB decision
Mitsubishi Heavy E35 is usually repair-first if a sensor or harness reading is confirmed. Board replacement should wait until the sensor circuit is tested.
Sensor replacement is usually targeted when resistance or voltage readings are out of range.
Harness or connector damage can look like a sensor fault until continuity is checked.
PCB replacement is a later step if the sensor and wiring test correctly.
Mitsubishi Heavy E35 questions
What does the Mitsubishi Heavy E35 error mean?
Can I fix a Mitsubishi Heavy E35 error myself?
Is it safe to keep running the aircon with a E35 error?
What causes a Mitsubishi Heavy E35 error?
Will a Mitsubishi Heavy E35 error need a repair or a full replacement?
What should I send a technician about a Mitsubishi Heavy E35 error?
Confirm the fault
Share the error code, model number and symptoms so we can assess the likely cause.
Not the right code?
Browse the full Mitsubishi Heavy list or check a few codes in the same fault category.
Ready to get started?
Tell us what’s going on. Symptoms, setup, photos, anything we should know. We’ll assess and come back with the right next step.
Read next
Use these if the quote mentions the parts, checks, or repair path this code points to.