Skip to main content

Mitsubishi MXY-4H33VG vs Panasonic CU-4XU33YBZ in Singapore

Mitsubishi Electric MXY-4H33VG and Panasonic CU-4XU33YBZ both deliver nearly 7.0 kW of 5-tick System 4 cooling for 4-room HDB flats. MXY-4H33VG leads on weighted COP (5.76 vs 5.61) and annual energy cost (S$714 vs S$730), while CU-4XU33YBZ emphasises active indoor air purification.

On this page

NEA 5-tick performance comparison for 4-room flats

Under the November 2026 NEA product registry, Mitsubishi Electric MXY-4H33VG is rated at 6.93 kW with a 4.86 full-load COP and 5.76 weighted COP, drawing an estimated 2,646 kWh or S$714 annually. Panasonic CU-4XU33YBZ produces a nearly identical 6.96 kW at 4.88 full-load COP, but its 5.61 weighted COP raises the estimated yearly electricity figure to S$730.

That 0.15 gap in weighted COP reflects part-load efficiency when only one or two bedrooms run overnight. Households running master bedroom cooling every night for eight hours generally see slightly steadier SP Group bills from the Starmex outdoor unit.

NEA 5-tick performance comparison for 4-room flats summary table
Metric (NEA Nov 2026)Mitsubishi Electric MXY-4H33VGPanasonic CU-4XU33YBZ
Rated cooling capacity6.93 kW (approx. 23,600 BTU/h)6.96 kW (approx. 23,750 BTU/h)
Full-load / weighted COP4.86 / 5.764.88 / 5.61
NEA annual energy estimateS$714/yr (2,646 kWh)S$730/yr
Indoor hygiene highlightEasy Clean removable louver designBuilt-in nanoe X hydroxyl radical mode
Best flat layout fitOvernight bedroom runners seeking quick maintenanceHomes wanting odour reduction and app scheduling

Routine servicing access and indoor air features

Mitsubishi Electric designs its Starmex indoor fancoils around rapid mechanical cleaning: front louvers swing wide so technicians and homeowners can inspect blower wheels early before slime builds up in Singapore humidity. Replacement sensors, fan motors, and complete PCBs also enjoy broad local stock.

Panasonic counters with nanoe X air treatment on compatible XU wall units, which can run in fan-only operation to inhibit stale kitchen or pet smells, paired with Comfort Cloud WiFi control. Both brands still require periodic chemical cleaning and drain flushing because electronic air treatment does not clear wet condensate jelly.

Choosing between both condensers for HDB ledges

At roughly 7.0 kW total condenser output, neither machine is meant for simultaneous full-blast cooling across a large west-facing living hall and three bedrooms at midday. Both thrive when one living-area unit operates by day and bedrooms take over after sunset.

Confirm copper pipe gauge, Class 0 insulation thickness, and HDB bracket certification before signing any package, because poor piping workmanship causes more early cooling loss than the 0.03 kW specification difference between these two Japanese condensers.

Common questions

Is Mitsubishi Electric MXY-4H33VG more energy-efficient than Panasonic CU-4XU33YBZ?
Mitsubishi Electric MXY-4H33VG achieves a higher NEA weighted COP of 5.76 versus 5.61 for Panasonic CU-4XU33YBZ, translating to S$714 versus S$730 in estimated yearly electricity use. Part-load bedroom operation favours the Starmex inverter slightly, though actual bills still hinge on set temperature and filter cleanliness.
Can either System 4 condenser cool four rooms simultaneously in Singapore?
Running all four indoor units together on a 6.93 kW or 6.96 kW outdoor condenser splits available cooling across every room, slowing pull-down during hot afternoons. Households wanting heavy concurrent living-hall and bedroom cooling should step up to 8.0 kW-class condensers instead.
Does Panasonic nanoe X replace regular aircon servicing in humid flats?
Panasonic nanoe X helps inhibit airborne odours and surface microbes, yet condensate pans, blower drums, and drainage pipes still collect dust and algae biofilm in Singapore's tropical climate. Scheduled general cleaning and occasional chemical coil washes remain essential to stop water leaks.
How do spare parts and PCB replacements compare between Starmex and Panasonic?
Both Japanese brands maintain established Singapore distribution networks for replacement thermistors, fan motors, and complete PCBs, since faulty circuit boards are swapped as whole assemblies rather than soldered. Mitsubishi Electric Starmex enjoys especially deep third-party stock across local wholesale counters.

Sources