Mitsubishi Electric aircon 13 / LED1 9x, LED2 off
Use this Mitsubishi Electric 13 / LED1 9x, LED2 off blinking light guide to capture the fault correctly and see what should be checked before parts are quoted.
What does Mitsubishi Electric 13 / LED1 9x, LED2 off mean?
Mitsubishi Electric 13 / LED1 9x, LED2 off is listed as bus-bar voltage protection in Multi-Split rows such as FP Series, Starmex R32. The loaded row is source-backed by official diagnostic material. Confirm the exact model, series, or signal row before accepting a parts quote.
Voltage, current, fuse, module, or power-supply protection has been triggered.
Loose connector, damaged harness, or outdoor electrical component fault.
PCB or inverter-module issue after power and load checks are confirmed.
What to do now
Use these steps before customer action or a parts quote.
Stop using the unit if 13 / LED1 9x, LED2 off returns
Stop repeated restarts if 13 / LED1 9x, LED2 off returns, trips power, smells burnt, or the outdoor unit runs unusually hot.
No manufacturer reset steps listed for 13 / LED1 9x, LED2 off
Capture the complete 13 / LED1 9x, LED2 off pattern and model stickers first. The selected source row lists no customer reset procedure; do not treat a generic power-cycle as manufacturer guidance.
Send these to us
13 / LED1 9x, LED2 off blinking light, a short video of the blinking-light sequence, Mitsubishi Electric model stickers, affected rooms, operating state when the code appeared, and trip timing and outdoor-unit behaviour
Source-specific guidance
These diagnostic-reference notes help match the code to the exact model. Electrical, refrigerant, wiring, resistance, and component checks are technician work, not DIY steps.
| Source detail | What it says |
|---|---|
| Diagnostic note | Do not keep resetting the system if this pattern returns. Record the model number, lamp or LED pattern, and affected rooms before booking diagnosis. |
| Singapore / model note | Official Mitsubishi Electric checklist action: Replace inverter P.C. board. |
What to check before repair
Use this split to separate safe evidence capture from the tests a technician should prove before quoting parts.
| You can check | Technician should confirm |
|---|---|
| Before taking any system action on 13 / LED1 9x, LED2 off, take a short video of the blinking-light sequence. | Confirm whether 13 / LED1 9x, LED2 off is voltage, current, module, fuse, or protection related. |
| Capture the Mitsubishi Electric indoor and outdoor model stickers so the correct family row is used. | Check incoming voltage, connectors, inverter module, and current draw under load. |
| The selected source row lists no customer reset procedure. Note whether one room, several rooms, or the whole system is affected. | Confirm downstream loads before replacing electrical boards or modules. |
What changes the next step
These clues decide whether the first check is room-side, shared outdoor-side, refrigerant-side, source-table, or model-family confirmation.
| What you see | What it points to |
|---|---|
| Only one indoor unit shows 13 / LED1 9x, LED2 off. | The affected room, indoor board path, wiring route, or local component should be checked first. |
| Several rooms or the outdoor unit show the same 13 / LED1 9x, LED2 off fault. | Prioritise the shared outdoor side, power path, and source-listed system branch. |
| The fault remains displayed or returns during operation. | Start with the source-row diagnostic branch before approving parts. |
| The model family is different from the row you found online. | Use the model or series filter first; same-looking codes can still belong to different diagnostic tables. |
| The model belongs to Multi-Split rows such as FP Series, Starmex R32. | The loaded row is source-backed by official diagnostic material. Use the matching source row before quoting parts. |
Electrical module or wiring decision
Mitsubishi Electric 13 / LED1 9x, LED2 off needs voltage, current, module, and load checks before parts are quoted. The repair path depends on whether the fault is supply-side, wiring-side, or board-side.
Supply voltage and load checks separate building-side issues from unit-side faults.
Module or inverter faults need measured current and voltage evidence.
Repeated electrical trips should not be cleared repeatedly without diagnosis.
Mitsubishi Electric 13 / LED1 9x, LED2 off questions
What does the Mitsubishi Electric 13 / LED1 9x, LED2 off error mean?
Can I fix a Mitsubishi Electric 13 / LED1 9x, LED2 off error myself?
Is it safe to keep running the aircon with a 13 / LED1 9x, LED2 off error?
What causes a Mitsubishi Electric 13 / LED1 9x, LED2 off error?
Will a Mitsubishi Electric 13 / LED1 9x, LED2 off error need a repair or a full replacement?
What should I send a technician about a Mitsubishi Electric 13 / LED1 9x, LED2 off error?
Confirm the fault
Share the error code, model number and symptoms so we can assess the likely cause.
Not the right code?
Browse the full Mitsubishi Electric list or check a few codes in the same fault category.
Ready to get started?
Tell us what’s going on. Symptoms, setup, photos, anything we should know. We’ll assess and come back with the right next step.
Read next
Use these if the quote mentions the parts, checks, or repair path this code points to.