Mitsubishi Electric aircon 22 / LED1 8x, LED2 lit blinking light
Use this Mitsubishi Electric 22 / LED1 8x, LED2 lit blinking light guide to decide when to stop resetting, what to capture, and what to check before parts are quoted.
What does Mitsubishi Electric 22 / LED1 8x, LED2 lit mean?
Mitsubishi Electric 22 / LED1 8x, LED2 lit is listed as converter protection in Multi-Split rows such as FP Series, Starmex R32. The loaded row is source-backed by official diagnostic material. Confirm the exact model, series, or signal row before accepting a parts quote.
Voltage, current, fuse, module, or power-supply protection has been triggered.
Loose connector, damaged harness, or outdoor electrical component fault.
PCB or inverter-module issue after power and load checks are confirmed.
What to do now
Use these steps before another reset or parts quote.
Stop using the unit if 22 / LED1 8x, LED2 lit returns
Stop repeated restarts if 22 / LED1 8x, LED2 lit returns, trips power, smells burnt, or the outdoor unit runs unusually hot.
Reset 22 / LED1 8x, LED2 lit once
Capture the 22 / LED1 8x, LED2 lit pattern, then reset once only if there is no burning smell, repeated trip, or hot outdoor unit.
Send these to us
22 / LED1 8x, LED2 lit blinking light, a short video of the blinking-light sequence, Mitsubishi Electric model stickers, affected rooms, reset result, and trip timing and outdoor-unit behaviour
Source-specific guidance
These diagnostic-reference notes help match the code to the exact model. Electrical, refrigerant, wiring, resistance, and component checks are technician work, not DIY steps.
| Source detail | What it says |
|---|---|
| Source repair action | Do not keep resetting the system if this pattern returns. Record the model number, lamp or LED pattern, and affected rooms before booking diagnosis. |
| Singapore / model note | Official Mitsubishi Electric checklist action: Check power supply voltage and replace inverter P.C. board if needed. |
What to check before repair
Use this split to separate safe evidence capture from the tests a technician should prove before quoting parts.
| You can check | Technician should confirm |
|---|---|
| Before resetting 22 / LED1 8x, LED2 lit, take a short video of the blinking-light sequence. | Confirm whether 22 / LED1 8x, LED2 lit is voltage, current, module, fuse, or protection related. |
| Capture the Mitsubishi Electric indoor and outdoor model stickers so the correct family row is used. | Check incoming voltage, connectors, inverter module, and current draw under load. |
| Note whether one room, several rooms, or the whole system is affected, plus whether it returns after one reset. | Confirm downstream loads before replacing electrical boards or modules. |
What changes the next step
These clues decide whether the first check is room-side, shared outdoor-side, refrigerant-side, source-table, or model-family confirmation.
| What you see | What it points to |
|---|---|
| Only one indoor unit shows 22 / LED1 8x, LED2 lit. | The affected room, indoor board path, wiring route, or local component should be checked first. |
| Several rooms or the outdoor unit show the same 22 / LED1 8x, LED2 lit fault. | The shared outdoor side, power path, communication trunk, or refrigerant circuit needs priority checking. |
| The fault returns immediately after one reset. | Start with the source-row diagnostic branch before approving parts. |
| The model family is different from the row you found online. | Use the model or series filter first; same-looking codes can still belong to different diagnostic tables. |
| The model belongs to Multi-Split rows such as FP Series, Starmex R32. | The loaded row is source-backed by official diagnostic material. Use the matching source row before quoting parts. |
Electrical module or wiring decision
Mitsubishi Electric 22 / LED1 8x, LED2 lit needs voltage, current, module, and load checks before parts are quoted. The repair path depends on whether the fault is supply-side, wiring-side, or board-side.
Supply voltage and load checks separate building-side issues from unit-side faults.
Module or inverter faults need measured current and voltage evidence.
Repeated electrical trips should not be cleared repeatedly without diagnosis.
Mitsubishi Electric 22 / LED1 8x, LED2 lit questions
What does the Mitsubishi Electric 22 / LED1 8x, LED2 lit error mean?
Can I fix a Mitsubishi Electric 22 / LED1 8x, LED2 lit error myself?
Is it safe to keep running the aircon with a 22 / LED1 8x, LED2 lit error?
What causes a Mitsubishi Electric 22 / LED1 8x, LED2 lit error?
Will a Mitsubishi Electric 22 / LED1 8x, LED2 lit error need a repair or a full replacement?
What should I send a technician about a Mitsubishi Electric 22 / LED1 8x, LED2 lit error?
Confirm the fault
Share the error code, model number and symptoms so we can assess the likely cause.
Not the right code?
Browse the full Mitsubishi Electric list or check a few codes in the same fault category.
Ready to get started?
Tell us what’s going on. Symptoms, setup, photos, anything we should know. We’ll assess and come back with the right next step.
Read next
Use these if the quote mentions the parts, checks, or repair path this code points to.