Skip to main content

Daikin One Room Not Cold on Multi-Split: Causes and Checks

Single-room cooling loss on a Daikin multi-split confirms the shared outdoor compressor still works properly. When adjacent bedrooms stay icy cold, the fault sits strictly along the warm room branch: its FCU airflow, thermistor probe, expansion valve port, or pipe run.

On this page

Why one Daikin branch fails while other bedrooms stay cold

Multi-split Daikin condensers such as MKM75ZVMG and MKM85VVMG meter refrigerant separately to each bedroom through dedicated outdoor electronic expansion valves (EEVs) and branch copper lines. Because the shared compressor still chills neighbouring rooms, troubleshooting narrows sharply to components exclusive to the warm room.

Start by checking that the warm room remote is on cool mode at 20 C with dry, clean mesh filters, and test running that room alone for ten minutes. Avoid flipping electrical breakers or wall isolators to reset branch control logic.

Why one Daikin branch fails while other bedrooms stay cold summary table
Single-room test clueLikely branch faultTargeted repair
Weak breeze and cool fins behind thick dustHeavily choked single FCU blower and coilPerform general servicing or chemical wash on that FCU
Strong airflow, cools briefly then turns ambientDrifted room or indoor pipe thermistor probeMeasure sensor resistance and fit new OEM thermistor
Warm air continuously while other rooms stay icyStuck outdoor EEV solenoid coil or jammed valve portTest EEV coil ohms and replace faulty solenoid or valve
Faint hissing or frost near one branch valve on ledgeKinked branch copper pipe or isolated flare seepagePressure-test branch line, fix leak, and recharge accurately

Room thermistor drift versus stuck outdoor expansion valves

When an indoor room thermistor drifts out of calibration, it reports a falsely cool temperature back to the indoor PCB, telling the outdoor condenser to close off refrigerant flow to that room early. Replacing the small clip-in sensor restores accurate room tracking.

If sensors and airflow check out cleanly, technicians test the outdoor EEV coil driving that specific port on the ledge condenser. Should diagnostics instead uncover a failed indoor control board unable to command cooling demand, the faulty PCB is replaced as a complete OEM board rather than soldered.

Pinpointing the faulty Daikin branch quickly

Note whether the warm bedroom still blows room-temperature air when run solo with every other Daikin indoor unit switched off. That simple five-minute observation tells technicians immediately whether the problem is load-sharing or a closed branch valve.

WhatsApp your solo-run result, Daikin condenser model, and room layout to Snowflake Aircon Services to arrange focused branch testing without unnecessary whole-system guesswork.

Common questions

Why does running one Daikin bedroom alone help diagnose single-room cooling loss?
Testing the warm Daikin bedroom with every other indoor unit switched off isolates whether that branch can call the outdoor compressor at all. Zero cooling during solo operation points toward a drifted thermistor, stuck port expansion valve, or faulty indoor control board.
Can a single dirty bedroom FCU stop cooling while other Daikin rooms stay cold?
Heavily clogged mesh filters, dust-caked blower wheels, and dirty evaporator fins inside one nightly used bedroom severely restrict airflow and coil heat exchange. Neighbouring Daikin bedrooms with cleaner indoor coils continue blowing crisp cold air until that soiled fancoil receives thorough cleaning.
How do technicians test a stuck Daikin outdoor expansion valve port?
Technicians compare suction pipe temperatures across each outdoor branch line on the ledge while measuring electrical resistance across the suspect port EEV solenoid coil. An open-circuit coil or jammed metering needle prevents liquid refrigerant entering that single bedroom despite normal compressor pressure.
Does a low gas leak always affect every room on a Daikin multi-split equally?
Moderate refrigerant loss on a Daikin multi-split often starves the longest pipe run or highest-load bedroom first while shorter branch lines still feel moderately cool. Manifold pressure checks and branch temperature readings separate system-wide gas shortage from single-port valve faults.

Sources