Skip to main content

Mitsubishi Heavy Aircon Not Cold: Causes and Repair

A Mitsubishi Heavy unit that runs but stays warm most often has a setting, airflow or heat-load cause, or a fault in the refrigerant circuit. A RUN and TIMER blink pattern on the indoor unit points to the second group.

On this page

Why is my Mitsubishi Heavy aircon not cold?

Most cases come down to settings, blocked airflow or too much heat in the room. The rest are faults in the gas circuit or the compressor, which the unit often reports with a light pattern.

The MHI Singapore FAQ asks owners to check for ECONO mode, a blocked intake or outlet grille, and an open window or door. It adds that dusty filters restrict airflow and that a frozen indoor coil gives insufficient cooling.

The general fault path for any brand is in the aircon not cold guide. The table below is the MHI version.

Why is my Mitsubishi Heavy aircon not cold? summary table
What you seeLikely causeNext step
Cool but weak, no lights flashingECONO mode, open door or blocked grilleCorrect the setting or clear the grille
Weak airflow from the ventsDusty filters or coilServicing
Ice on the indoor coilAirflow or refrigerant problemSwitch off and book a check
RUN or TIMER light blinkingGas, sensor or compressor faultCount the pattern and note the model
Cooling fades a little each weekRefrigerant leakLeak test before any gas

Which MHI light patterns point to gas or the compressor

Three rows in MHI Air Conditioning Europe's service handbook for inverter wall units matter most when the room stays warm. The RUN light counts first and the TIMER light second.

RUN 7 times with TIMER on is E57, refrigeration protective control. MHI lists a closed service valve or insufficient refrigerant. RUN on with TIMER 5 times is E36, compressor overheat, from low gas, a faulty discharge pipe sensor or a closed valve.

RUN 2 times with TIMER 2 times is E60, rotor lock, meaning the compressor cannot turn. The causes listed are a faulty compressor, an open phase or a faulty outdoor board.

The handbook is a European document for its own model series, so the manual for the unit on your wall decides the reading. The full tables sit in the mitsubishi heavy blinking light guide, and leak points in the MHI blinking light gas leak guide.

Should a Mitsubishi Heavy that stops cooling be topped up with gas?

A top-up is not the fix. MHI Singapore states that a correctly installed and charged system never needs more gas, and that regular top-ups mean a leak.

So the technician pressure-tests the circuit, traces and repairs the leak, and only then recharges. E57 and E36 also list a closed valve and a sensor, which no amount of gas corrects.

Repair or replace a Mitsubishi Heavy that has lost cooling

Warranty comes first. MHI Singapore's terms give 12 months on all parts and 5 years on the compressor only, with labour and gas refills excluded. Warranty repairs must go through KM Marketing or its appointed agents, and the unit must have been registered within 14 days of purchase. The mitsubishi heavy warranty guide covers the rest.

Outside warranty, a sensor, a closed valve or a single joint leak is normally worth fixing, and a failed outdoor board is replaced with a new one. A rotor lock on an older system is the case for pricing a replacement against the repair.

The NEA register on 21 November 2026 lists 20 Mitsubishi Heavy entries: 15 single split and 5 multi split, each rated 4 or 5 ticks. Book a diagnostic visit to have the blink pattern read and the circuit tested.

Common questions

Why is my Mitsubishi Heavy aircon running but not cold?
The MHI Singapore FAQ points first to ECONO mode, a blocked intake or outlet grille, an open window or door, and dusty filters. A frozen indoor coil also gives insufficient cooling. When those are ruled out, or a RUN or TIMER light is blinking, a gas, sensor or compressor fault is the likely cause.
What does RUN 7 times and TIMER on mean on a Mitsubishi Heavy aircon?
In MHI Air Conditioning Europe's service handbook for inverter wall units, RUN 7 times with TIMER on is E57, refrigeration protective control. The listed causes are a closed service valve or insufficient refrigerant. Patterns vary by series, so the manual for the installed model confirms the reading before any repair is quoted.
Does a Mitsubishi Heavy aircon that is not cold just need gas?
Gas alone rarely fixes it. MHI Singapore says a correctly charged system never needs topping up, and that regular top-ups mean the system is leaking. The leak is located and sealed before any recharge, and a closed valve or faulty sensor can produce the same symptom without any gas loss.
Who repairs a Mitsubishi Heavy aircon under warranty in Singapore?
MHI Singapore's terms say warranty repairs must be done by KM Marketing Pte Ltd or its appointed agents. Cover is 12 months on all parts and 5 years on the compressor only, labour and gas refills are excluded, and the unit has to be registered within 14 days of purchase.

Sources