Skip to main content

Panasonic Aircon Won't Turn On: Causes and What to Check

A Panasonic aircon with no response is first checked for weak remote batteries, a tripped breaker and a set timer, the three checks Panasonic lists. A tripped breaker is left off for a technician, and a blinking timer lamp means a stored fault code.

On this page

Why won't my Panasonic aircon turn on?

When the unit does not work, Panasonic's Canadian operating instructions for its CS-E wall units name three things to look at. They are the remote batteries, a tripped circuit breaker and a timer that has been set.

The general power checks in aircon cannot turn on apply to every brand. Singapore models may differ from the Canadian and European units these sources cover. Panasonic adds its own lamp and timer signals, set out in the table.

Why won't my Panasonic aircon turn on? summary table
What happensWhat Panasonic saysNext step
Remote display dim, or signal weakBatteries inserted wrongly or weakFit new batteries of the same type
Remote works, unit ignores itReceiver blocked, or some fluorescent lights interferingClear the receiver; consult a dealer if it persists
Aircon breaker trippedFrequent trips need an authorised dealerKeep it off; have the circuit checked
Power lamp blinks before the unit is onPreparing to run because the ON timer is setNormal, no action
Power lamp blinks slowly, long on and short offStandby mode, per the service manualNormal, no action
Cooling starts about 3 minutes after a stopCompressor restart delay after a stopNormal, wait it out
Unit stays off after a power cutAutomatic restart does not apply when a timer is setLook at the timer settings
Unit stops and the timer lamp blinksA fault code has been storedRetrieve the code for the technician
Unit stops the moment it is switched onAn abnormality: stop using itSwitch off at the breaker; book a technician

Checks that need no tools

A timer lamp that blinks after the unit stops is a stored code, not a timer setting.

  • Fit new batteries of the same type. Panasonic warns that rechargeable Ni-Cd cells can damage the remote.
  • Look at the aircon breaker in the DB box. If it has tripped, do not switch it back on; have the circuit tested.
  • Make sure nothing blocks the indoor unit's signal receiver.
  • Look at the timer settings on the remote. A power failure can cancel a timer, and Panasonic says it can be set again from the remote.

Leave it off, or keep trying?

Leave the breaker off when it trips. Panasonic lists a circuit breaker that switches off frequently among the conditions where power goes off at the breaker and an authorised dealer takes over.

The same holds for a burning smell, a power cord that turns abnormally hot, or a unit that stops as soon as it is switched on. For each, Panasonic tells owners to stop using the unit and turn off the breaker.

A wait after switching on again is normal. Panasonic's European service manual for its CS-E PKEW wall units holds the compressor off for 3 minutes from the moment operation stops.

What a technician tests, and when the board is replaced

The technician reads any stored code first; the codes and check mode are set out under panasonic check mode.

The European service manual sets H11 when the indoor and outdoor units fail to talk after a minute of running. The test then goes to the connecting wire, its terminals and the boards.

Panasonic's instructions leave repairs and internal cleaning to an authorised dealer or specialist, so keep the panels closed. Snowflake Aircon Services fits a new board when one has failed, and does not repair boards. On a unit still under cover, read the panasonic aircon warranty before booking.

Common questions

Why is my Panasonic aircon not turning on?
Panasonic's Canadian operating instructions name three things to look at if the unit does not work: remote batteries fitted correctly and not weak, a tripped circuit breaker, and a timer that has been set. A tripped aircon breaker stays off until the circuit and the unit have been checked.
Why did my Panasonic aircon not come back on after a power cut?
Panasonic's auto restart control resumes the previous operating mode some time after power returns, but Panasonic states that it does not apply when a timer is set. A power failure can also cancel a timer, and Panasonic says the timer can be set again from the remote.
Is a blinking power light on my Panasonic aircon a fault?
A power indicator that blinks before a Panasonic unit is switched on is not a malfunction, according to Panasonic, but a preliminary step when the ON timer has been set. A timer lamp that blinks after the unit stops is different, because it means a fault code has been stored.
Should I keep switching my Panasonic aircon on if the breaker keeps tripping?
A Panasonic unit that trips the breaker repeatedly should be switched off at the breaker and left for a technician. Panasonic's instructions list frequent breaker trips, a burning smell and a power cord that turns abnormally hot among the conditions where the unit stops being used.

Sources